Marine electronics in Montauk.
Chartplotters, radar, VHF, sounders and full helm rebuilds for boats on Block Island Sound and the Atlantic — installed at your dock in Montauk.
LIME is an NMEA Certified marine electronics installer working across Suffolk County. We come to the boat wherever it sits — Montauk Harbor, Star Island, Lake Montauk and the Gone Fishing basin. When you call, you get the person who does the work.
On this page
What We Do
Marine electronics installation in Montauk.
Every install is done to ABYC electrical standards — tinned marine wire, correctly rated fuses, labelled circuits and a load test before we leave. Most Montauk work is offshore fishing boats running the longest trips on Long Island, where radar, AIS and satellite internet are not optional.
Garmin, Simrad, Raymarine and Furuno displays sized to your helm, wired into a proper NMEA 2000 backbone so everything talks to everything.
Radar and AIS for running Block Island Sound and the Atlantic in fog, at night and in traffic. Mounted, aligned and tuned so the picture is actually usable.
Fixed-mount VHF with DSC, proper antenna runs and clean grounds — so you are heard the first time you call.
Transducer placement is the whole job. We put it where it reads at speed for charter and party boats, offshore sportfish and serious centre consoles, not just where it is easy to drill.
Custom fabricated panels when the factory dash will not take a modern display. Cut, finished and wired to look factory.
House banks, lithium conversions, charging and marine solar — all on the DC side, done properly.
Boating in Montauk
We know the water you run.
Boats out of Montauk run Block Island Sound and the Atlantic. Most are charter and party boats, offshore sportfish and serious centre consoles, launched and kept around Montauk Harbor, Star Island, Lake Montauk and the Gone Fishing basin. From there people head to the rips, Block Island, Cox Ledge and the canyons.
That matters for what you should have at the helm. Montauk boats are typically offshore fishing boats running the longest trips on Long Island, where radar, AIS and satellite internet are not optional. We size the electronics to how you actually use the boat — not to whatever is on the shelf.
We are on the water across Suffolk County every week. If you are in Montauk, we are not making a special trip — we are already nearby.
Ready to talk? Or keep reading below.
Our Process
How a Montauk job runs.
You get the person doing the work, not a call centre. Tell us the boat, where it sits in Montauk, and what you want it to do.
For anything substantial we come and look first — the helm, the wiring behind the dash, the cutout sizes. Guessing costs you money.
We go over time and labour costs with you before we start. Everything is time and materials — no fixed-price promises we cannot honour.
ABYC standards throughout — tinned wire, rated fuses, labelled circuits, sealed penetrations.
We power everything up, check the network, and walk you through it so you can actually use it.
60-day labour warranty. Equipment carries the manufacturer warranty. If something is not right, we come back.
Most Common Work
What we fix most on Montauk boats.
After enough seasons working Suffolk County, patterns show up. These are the jobs that come up again and again on boats kept around Montauk.
You bought the boat with the previous owner's electronics and no manuals. We work out what is actually there, what is worth keeping, and what should go.
House banks worn out from sitting all season. We test what you have, size the replacement properly, and sort the charging so it stops happening.
Weak VHF range is usually the antenna, the cable or the ground — not the radio. We test the whole run before anyone spends money on a new set.
A radar left on factory settings shows noise, not targets. We set gain, sea and rain clutter for the water you run.
Salt air gets into every crimp eventually. We find green, swollen terminals behind the dash more than anything else. We cut them out, re-terminate with tinned marine wire and heat-shrink the joints properly.
A sounder that reads fine at idle and goes blank on plane is almost always placement or a bad mount. We move the transducer into clean water and re-fair it so it reads when it matters.
Why It Matters
Local knowledge is part of the job.
Anyone can bolt a screen to a dash. Setting it up for where you actually run is different. Boats working Block Island Sound and the Atlantic out of Montauk need charts, ranges and alarms configured for that water — not left on factory defaults.
We set depth alarms for the water you run, put the chart detail where you need it, and configure radar guard zones for the traffic you actually encounter heading to the rips, Block Island, Cox Ledge and the canyons. It takes an extra half hour and it is the difference between electronics you trust and electronics you ignore.
We are also honest about what you do not need. If the boat does not justify a second display or a bigger radar, we will tell you. Selling you gear you will not use is a bad way to keep a customer in a town this size.
ABYC Electrical Standards
Empire Wind NETP Approved Vendor
5-Star Google Rating
Fully Insured
$140/hr · 4-Hour Minimum
60-Day Labour Warranty
Fair Pricing Up Front
What Boat Owners Say
Long Island boat owners, in their words.
"Booked out a few weeks but worth it. You can tell the difference when the person who quotes it is the person who wires it."
"Marked fish at thirty knots for the first time since I owned the boat. Turned out the transducer was in dirty water."
"Set up the plotter properly for where I actually run instead of leaving it on defaults."
Questions
Marine electronics in Montauk — common questions.
Do you service boats in Montauk?
Yes. LIME covers all of Suffolk County and the rest of Long Island, Montauk included. We come to your boat — at the dock, on the mooring, on the lift or on the trailer. Travel is billed one way, portal-to-portal, with a 4-hour minimum.
What does marine electronics installation cost in Montauk?
All work is time and materials — we never quote a firm fixed price. Labour runs at our NMEA MEI rate with a 4-hour minimum, portal-to-portal, and parts are billed at cost plus markup. We give you fair pricing up front so you know the scale of the job before we start.
Can you install electronics while my boat stays in Montauk?
Almost always. Most chartplotter, radar, VHF, sounder and NMEA 2000 work happens right where the boat sits on Block Island Sound and the Atlantic. Only bigger dash fabrication jobs are easier at a yard, and we will tell you up front if that is the case.
Which brands do you install?
Garmin, Simrad, Raymarine, Furuno, Icom, Fusion and more. LIME supplies all equipment we install — we do not fit customer-supplied gear, because we cannot warranty what we did not supply.
How long does a job in Montauk take?
A single chartplotter or VHF swap is usually one visit. A full helm with plotter, radar, sounder and an NMEA 2000 backbone is typically one to two days. We give you a realistic timeline up front rather than a best case.
Are you certified?
Yes — NMEA Certified MEI, working to ABYC electrical standards, fully insured, and an Empire Wind NETP approved vendor. Labour carries a 60-day warranty; equipment carries the manufacturer's warranty.
Can you work on older boats?
Yes, and a lot of our work is exactly that — modern displays fitted to boats whose wiring is decades old. We replace what is tired rather than building on top of it.
Do you supply the equipment?
Yes, and only equipment we supply. We do not install customer-supplied gear, because we cannot stand behind hardware we did not source.
Boat in Montauk? Let's get it sorted.
Call and you get the person doing the work. We come to the boat, look at what you have, and give you fair pricing up front.