Marine electronics in Islip.
Helm rewiring, 12-volt power, marine radios and chartplotters for boats on the canals, the town marinas and the Connetquot River, worked on at your dock in Islip and West Islip.
Here is the marine electronics Islip boat owners can hold us to so far: a 24-foot center console at a private dock in West Islip that needed its switch panel and helm power rebuilt, done over two days at the dock. We work on the boat’s 12-volt side. We come to the boat, whether it sits on a canal behind the house, at a town marina or up the Connetquot River. The phone is answered by the installer, not a dispatcher.
Recent Work, West Islip
Two days on one center console in West Islip.
This is the job we have written up from the Town of Islip. No names and no boat names, only what was wrong and what we did about it.
A 1997 Boston Whaler 24 Outrage, West Islip, August 2026
Two visits on back-to-back days at a private dock in West Islip. Day one was wiring and switches: three new feed lines run straight to the battery and the negative side, a switch panel that had been left disconnected rewired, four switches replaced, a universal serial bus (USB) charging port added, and every switch tested.
Day two was the helm. We took out the old power components behind the console, put in a new power block, rewired the helm from it, and installed a stereo amplifier with its own new power run. The photo below is the switch wiring before the rewire; the one at the top of the page is the new amplifier and power block going in.
The Water
Marine electronics Islip, from the Connetquot River to Nicoll Bay.
The Town of Islip faces the Great South Bay, and on its east side the Connetquot River opens into the bay and Nicoll Bay between Timber Point and Green Point. About a mile up the river, Oakdale has four marinas on its south shore, two of which take transient boats, according to the marinas.com guide to the river. Suffolk County runs Timber Point Marina in Great River, and the state’s launch list shows a town ramp at Great River where trailers need a Town of Islip permit.
River boats and bay boats ask different things of the electronics. Up a river, a depth sounder that reads true at slow speed and a chart with the channel drawn right matter more than radar range. Out on the open bay the order flips once the fog comes in. We set alarms, chart detail and radar settings for the water the boat actually runs, not for the factory demo.
Where Boats Are Kept
Town marinas, a county marina, and canals behind the houses.
West Islip Marina and Beach is a Town of Islip facility with seasonal slips and a ramp; a town permit is required. East Islip Marina Park is on Bayview Avenue. Bayberry Yacht Club lists an Islip address. We did not find a yacht club listed in West Islip, East Islip or Great River, so we will not pretend there is one.
Our West Islip job was at a private dock on a canal behind the house, and the boat stayed tied up there for both days of the work.
12 Volts Only
The 12-volt side of the boat, and where our work stops.
Everything we do on a boat runs on its 12-volt side: the batteries and their main feeds, the battery switches, the fuse and power blocks, the helm switch panel, and the electronics and lights those feed. That is marine electronics work, and it is what the West Islip job was.
We do not work on the 120-volt side. That means the shore-power cord and the dock pedestal, the shore-power inlet on the boat, the 120-volt panel and its breakers, the 120-volt outlets, ground-fault outlets included, and anything plugged into them. We are not licensed electricians, and that work belongs with one. If an outlet trips at the dock, call a licensed electrician; if the trouble is on the 12-volt side, call us.
On the 12-volt side, this is the order we work in, because it finds the fault without replacing parts on a hunch:
- The battery, its terminals and the main feed off it.
- The fuse or power block, one circuit at a time.
- Each switch, its fuse and the run to whatever it powers.
- The negative side, checked the same way as the positive.
We also do not work on air conditioning, generators or engines. Our marine electrician page draws the same line.
Center Console Helms
A helm power rebuild, and why it fixes more than one thing.
On an older center console, the power behind the helm grows one accessory at a time: a radio here, a stereo there, a light on a spare switch. After enough seasons you get the tangle in the before photo above. Loose crimps and shared feeds give you flickering displays, a radio that resets when the bilge pump starts, and switches that work only some of the time.
A rebuild puts one power block behind the console with its own fused feed for each circuit, labels every wire, and gives anything that draws real current, like a stereo amplifier, its own heavier run. If the boat is coming out for the season, a winter electronics refit is the easiest time to do it, with the console open and nobody waiting to go fishing.
Ready to talk? Or keep reading below.
How a Visit Works
Getting to your boat in Islip.
From Amityville, East Islip Marina is about 25 minutes in normal traffic, inside the 30 minutes of travel included in the first hour.
At a private dock, we need the boat reachable, the batteries charged, and the keys to anything locked. At a town marina, tell us the slip so nobody walks the docks looking. If the boat is on a trailer, a driveway works for most wiring jobs. Usually on your boat within two to three days.
Tell us the boat, the year, where it sits and what it is doing. A phone photo of the switch panel or the helm helps us bring the right parts the first time.
Rates
What marine electronics Islip visits cost.
Every job is billed on time and materials. The first hour is $280, and it covers setup and travel up to 30 minutes each way; after that it is $140 an hour, billed in 15-minute steps. A two-installer crew is $440 for the first hour, then $220 an hour. We supply the parts, and labor carries a 60-day warranty. Fair pricing, time and labor costs given up front.
There is no minimum and no separate setup line. A short fault hunt is billed by the quarter hour like everything else, and you see the time before we start.
Nearby
Harbors on either side of Islip.
Bay Shore is just west, where the Fire Island ferries leave from the Maple Avenue terminal. Babylon and Lindenhurst have their own pages with the jobs we have done there. East along the bay, Patchogue has the river and its two ferry terminals.
Somewhere else in the county? Start at our Suffolk County page, the town-by-town list, or the full range of marine electronics installation we do.
ABYC Electrical Standards
Empire Wind NETP Approved Vendor
5-Star Google Reviews
Fully Insured
$280 First Hour · $140/hr After
60-Day Labor Warranty
Fair Pricing Up Front
Reviews
Three Google reviews, unedited.
★★★★★ Rich F.
"Great install by David and his team! Complete electronics update, with new panels, gauges & switches. David is very meticulous, detail oriented in his planning and installation. Great communication throughout the process, and finished the project on-time."
★★★★★ Vanessa O.
"David is the ultimate professional. He installed a new radar and AIS on our boat in up state New York. He knows all the systems and is able to troubleshoot and provide solutions. No job is too big or too small. Highly recommend him!"
★★★★★ Tommy C.
"On time. Knowledgeable. Dependable. Reasonable."
Questions
Helm wiring and 12-volt questions from Islip.
My ground-fault outlets keep tripping at the dock. Can you fix that?No. Ground-fault outlets are on the boat’s 120-volt side, with the shore-power cord, the pedestal and the 120-volt panel. We are not licensed electricians and we do not work on that side, so call a licensed electrician for it. If the trouble is on the 12-volt side, we are the right call.
No. Ground-fault outlets are on the boat’s 120-volt side, with the shore-power cord, the pedestal and the 120-volt panel. We are not licensed electricians and we do not work on that side, so call a licensed electrician for it. If the trouble is on the 12-volt side, we are the right call.
Why do my helm switches work only some of the time?
Usually a loose crimp, a corroded terminal or one feed shared by too many circuits. We trace it from the battery and the power block out to the switch. On an older helm, a rebuild with its own fused feed for each circuit fixes the cause instead of one switch at a time.
My stereo amplifier cuts out when the music gets loud. Is the amplifier bad?
Often it is not. An amplifier pulls hard on bass notes, and a thin or shared power feed sags until the amplifier protects itself and shuts off. A dedicated, fused, heavier feed from the power block is the usual fix, and we check the ground at the same time.
Do you work at the West Islip and East Islip town marinas?
Yes. We come to the boat at a town slip just as we do at a private dock. The marina’s own rules on contractors and hours apply, so tell us the slip when you call.
Will you look at my air conditioner or generator while you are on board?
No. We do not work on air conditioning or generators. If a problem follows either one, we tell you plainly that it needs that technician, rather than bill time guessing.
Switches dead or a helm that flickers in Islip? Call.
Send the boat, the dock and what it is doing. We respond within one business day.